6 min read

Hardness or Corrosion: Reading a Steel Data Sheet

Every instrument steel arrives with a data sheet, and almost every specification argument comes down to two numbers on it that pull in opposite directions: hardness and corrosion resistance. Understanding why they conflict — and where the exceptions are — is most of what material selection for instruments consists of.

What the tensile test actually reports

The test is simple in principle: apply increasing elongation to a machined sample, flat or cylindrical to ASTM and ISO specification, and measure the force. What makes it useful is that the resulting curve has two distinct zones.

In the elastic zone, elongation is a fraction of a percent and fully reversible — remove the stress and the sample returns to its original length. The zone ends at the yield strength, defined as the point where permanent elongation reaches 0.2 %. That definition is a convention, not a physical event, which is why the figure is always written YS 0.2.

In the plastic zone, elongation becomes large — several percent, and up to 50 to 60 % for common metals — and nothing returns. Stress keeps rising as the test proceeds because of cold working, until the sample breaks at the ultimate tensile strength. Both YS and UTS are reported in N/mm², identical in value to MPa.

Three further parameters matter in design work:

  • Elasticity modulus E, in N/mm² — the figure used in design calculations.
  • Poisson’s ratio, the transverse modulus — remarkably, always around 0.3 for all metals.
  • Elongation at break, calculated as (Lu − L0) / L0 × 100. Below 5 % the material counts as brittle. For an instrument that may be struck or torqued, this is the number that predicts sudden failure.

Two standards govern the test, NF EN 10002 and ASTM E8, and they differ specifically in how the initial gauge length L0 is measured — enough to make figures from different sources not strictly comparable.

Hardness: three tests, different jobs

Hardness is resistance to penetration, and the choice of test is dictated by the material and the surface you have.

Brinell presses a 10 mm ball — steel or carbide — under 3,000 kg and the print diameter is read with a magnifying glass. It suits softer, lower-strength metals, needs no prepared surface, and is governed by ASTM E10 and EN ISO 6506.

Rockwell, reported as HRc, uses a diamond cone under 150 kg, measuring penetration between a 15 kg pre-load and the full load of 15 + 135 kg. It is the test for hardened steels and is performed after heat treatment — but it requires a prepared, typically ground surface. Standards: ASTM E18 and EN ISO 6508.

Vickers completes the set. All three are inexpensive and usually non-destructive, and all three give only a rough estimate of mechanical strength — useful for verification, not for design.

Three families, one standard

Instrument steels are specified to ASTM F899, and they fall into three metallurgical families.

Martensitic steels

Used in the hardened-and-tempered condition. These are the classic cutting-instrument steels, and their behavior is driven almost entirely by carbon content.

Precipitation-hardening martensitic steels

Hardened by precipitation of copper or titanium within the atomic structure, through a tempering step known as aging. The critical process detail: they are delivered martensitic and hardened, then aged at 480 °C after machining. The sequence is not optional — machining comes first, aging second.

Austenitic steels

Roughly 18 % chromium with at least 8 % nickel, in a face-centered cubic structure that is independent of temperature and heat treatment. They cannot be hardened by heat treatment at all — only by cold working.

Carbon buys hardness and costs corrosion resistance. Nearly every grade in the standard is a position on that trade-off.

Where the grades land

Grade Key figures Typical use Note
420A / 1.4021 0.20 % C, 13 % Cr, 43 HRc, UTS 1,450, YS 1,150 Cutting tools Limited corrosion resistance
420B / 1.4028 0.30 % C, 13 % Cr, 52 HRc, UTS 1,750, YS 1,500 Cutting tools Limited corrosion resistance
420C / 1.4034 0.45 % C, 13 % Cr, 52 HRc General use, cutting tools Limited corrosion resistance
420F / 1.4197 0.35 % C, 13 % Cr, 52 HRc Bar turning Limited corrosion resistance
431 / 1.4057 0.15 % C, 17 % Cr, 2 % Ni, 42 HRc, UTS ~1,000 Small drills Usual delivery condition
440A / 440B 0.70 to 0.90 % C, 17 % Cr, 0.5 % Mo, 56 to 57 HRc Cutting tools Limited corrosion resistance
440C / 1.4125 1.0 % C, 17 % Cr, 60 HRc Cutting tools Hardest of the family
420 Mod / 1.4123 0.4 % C, 15.5 % Cr, 2 % Mo, 0.3 % V, 0.2 % N, 59 HRc Cutting tools Very good corrosion resistance
630 / 1.4542 0.06 % C, 16.5 % Cr, 4 % Ni, 4 % Cu, 43 HRc, UTS 1,350 Non-cutting instruments, rasps Forgiving heat treatment
XM16 / 1.4543 12 % Cr, 8.5 % Ni, 48 HRc, UTS 1,600, YS 1,500 Drivers, control drills Torque instruments
S11100 12 % Cr, 11 % Ni, 2 % Mo, 49 HRc, UTS 1,650, YS 1,510 Drivers, drills, tap guides High-end quality
S46500 12 % Cr, 11 % Ni, 1 % Mo, 1.5 % Ti, 49 HRc Drivers, drills, tap guides Cold working raises aged HRc
S13800 12.5 % Cr, 8 % Ni, 2.25 % Mo, 46 HRc, UTS 1,550 Drivers, drills, tap guides Torque applications
S47500 11 % Cr, 8 % Ni, 5 % Mo, 8.5 % Co, UTS 2,100, YS 2,000 Drivers, drills, tap guides Cold working raises aged HRc
301 / 304 / 316 and L variants Annealed UTS 600, YS 200; cold-worked 900 to 1,200 Non-cutting guides, bushings 301 reaches 2,000 cold-worked
Hardness in HRc — and what it costs 440C420 Mod PH gradesAustenitic 6059 46–49not hardenable Same hardness class, opposite corrosion behavior: 420 Mod adds molybdenum, vanadium and nitrogen.
440C and 420 Mod sit one HRc point apart, but only one of them carries very good corrosion resistance. Alloying, not carbon alone, is what breaks the trade-off.

The specification shortcutCutting edge and no compromise on hardness: the high-carbon martensitic grades, accepting limited corrosion resistance. Cutting edge and corrosion resistance: 420 Mod. Torque transmission — drivers, taps, guides: the 12 % chromium precipitation-hardening grades at 46 to 49 HRc with yield strengths of 1,450 upward. Guides and bushings with no cutting duty: austenitic, cold-worked to the strength you need.

FAQ

Why is yield strength defined at 0.2 % elongation?

Because the transition from elastic to plastic behavior is gradual rather than a sharp event, so the standard fixes a convention: the stress at which permanent elongation reaches 0.2 %. Note also that NF EN 10002 and ASTM E8 differ in how the initial gauge length is measured, so elongation figures from different sources are not always directly comparable.

Can austenitic stainless steels be hardened for instrument use?

Not by heat treatment. Their face-centered cubic structure is independent of temperature and heat treatment, so the only route to higher strength is cold working — which takes them from UTS 600 N/mm² annealed to 900–1,200, and in the case of grade 301 as far as 2,000. That is why they appear in non-cutting roles such as guides and bushings.

Why must precipitation-hardening grades be machined before aging?

Because aging at 480 °C is what develops the final hardness through precipitation of copper or titanium. Machining first, aging second means cutting is done in the more workable condition, and the part reaches its specified hardness — 43 to 49 HRc depending on grade — only once its geometry is finished.